Hello,
I've run into a strange bug on the Vols tab. edit ** I'm using version 2.3.12 on a Mac **
The 'Water Available From Mash' field is inconsistent - it appears that the calculation sometimes forgets to subtract the Lauter Tun Loss set in my equipment profile.
Example -
Lauter Ton Loss is set to .25 gallons in my equipment profile.
Mash Grain Wt = 10.5 lb
Grain Abs calculated at 1.31 Gal
Tot Mash Water Adds = 3.75
Mash Tun Deadspace = .25 Gal
Adjust Mash Volume for Deadspace = NOT checked.
Water Available From Mash calculated at 2.19 -- that makes sense. 3.75 - 1.31 = 2.19
Sparge Vol calculated at 5.06
Est Pre-Boil Vol calculated at 7.25 --that also works. 2.19 + 5.06 = 7.25
Now if I check the Adjust Mash Volume for Deadspace box I get these:
Total Mash Water Adds = 4.00
Water Available From Mash = 2.44
Sparge Vol = 4.81
-- All good. Still equals my Est Pre-Boil Vol of 7.25
Here where it gets goofy.
If I leave the box checked and click on any other tab (Session, Design, Mash etc) and come back to the vols tab I get this:
Total Mash Water Adds = 4.00
Water Available From Mash = 2.69
Sparge Vol = 4.81
2.69 + 4.81 = 7.5
Est Pre-Boil Vol still calculates at 7.25 Gal.
If I uncheck the box I get the same results as when I first checked the box
If I leave that tab and come back to it I get the same results as when before I checked the box.
Does that make sense? Would screenshots be helpful?
I've run into a strange bug on the Vols tab. edit ** I'm using version 2.3.12 on a Mac **
The 'Water Available From Mash' field is inconsistent - it appears that the calculation sometimes forgets to subtract the Lauter Tun Loss set in my equipment profile.
Example -
Lauter Ton Loss is set to .25 gallons in my equipment profile.
Mash Grain Wt = 10.5 lb
Grain Abs calculated at 1.31 Gal
Tot Mash Water Adds = 3.75
Mash Tun Deadspace = .25 Gal
Adjust Mash Volume for Deadspace = NOT checked.
Water Available From Mash calculated at 2.19 -- that makes sense. 3.75 - 1.31 = 2.19
Sparge Vol calculated at 5.06
Est Pre-Boil Vol calculated at 7.25 --that also works. 2.19 + 5.06 = 7.25
Now if I check the Adjust Mash Volume for Deadspace box I get these:
Total Mash Water Adds = 4.00
Water Available From Mash = 2.44
Sparge Vol = 4.81
-- All good. Still equals my Est Pre-Boil Vol of 7.25
Here where it gets goofy.
If I leave the box checked and click on any other tab (Session, Design, Mash etc) and come back to the vols tab I get this:
Total Mash Water Adds = 4.00
Water Available From Mash = 2.69
Sparge Vol = 4.81
2.69 + 4.81 = 7.5
Est Pre-Boil Vol still calculates at 7.25 Gal.
If I uncheck the box I get the same results as when I first checked the box
If I leave that tab and come back to it I get the same results as when before I checked the box.
Does that make sense? Would screenshots be helpful?