Author Topic: BS2: evaporation rate, could I adjust it?  (Read 4581 times)

Offline Slurk

  • Slurk
  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 370
  • Life is too short!
    • SLURK BEER  By Foeyn Minibryggeri
BS2: evaporation rate, could I adjust it?
« on: October 01, 2012, 05:19:09 AM »
Hi,
Due to a larger post boil volume than calculated I would like to adjust the evaporation rate in BS2 (default 8,4%/hour). I can't find this possibility in the profile set up. Is this correct, or...? Any advice?
Regards,
Slurk
Ad Fundum!

Ready to drink: Slurk Fjellbrygg, Slurk Foeyn Ale, Slurk Agurk (Cucumber Wit), Slurk Belgian Blonde, Slurk Eng (Raspberry Wit), Slurk Hav (Seaweed Wit)
Aging: Slurk Whirled White Wheat (Wit)
Fermenting:
Next brew: Slurk Hav

Offline pcollins

  • BeerSmith Master Brewer
  • ****
  • Posts: 69
  • BeerSmith 2 Rocks!
Re: BS2: evaporation rate, could I adjust it?
« Reply #1 on: October 01, 2012, 06:58:18 AM »
Funny, I JUST did this for my brew day start. Same thing has been happening to me but I didn't really worry about it. Just got to tinkering with it this morning and adjusted it to see how my numbers turn out later.

When you're in the design portion of your recipe just click on the check mark that's beside the pull down menu for the Equipment profile. There you can change your evaporation rate among other variables.

Offline BeerSmith

  • Brewer, Author, Patriot
  • BeerSmith Administrator
  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 5598
  • BeerSmith - take the guesswork out of brewing!
    • BeerSmith
Re: BS2: evaporation rate, could I adjust it?
« Reply #2 on: October 01, 2012, 09:42:07 AM »
Hi,
  Its in your equipment profile - as posted above you just edit the equipment profile to change it.

Brad
Get a free trial of BeerSmith 3 here

Offline Slurk

  • Slurk
  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 370
  • Life is too short!
    • SLURK BEER  By Foeyn Minibryggeri
Re: BS2: evaporation rate, could I adjust it?
« Reply #3 on: October 01, 2012, 10:56:00 AM »
Thanks a lott Brad/Pcollins!
I have changed the evaporation rate accordingly and made a new default for my equipment set up.

Yesterday I didn't see the relationship between "boil off", "boil off as an hourly rate" and "evaporation rate".

Regards,
Slurk
Ad Fundum!

Ready to drink: Slurk Fjellbrygg, Slurk Foeyn Ale, Slurk Agurk (Cucumber Wit), Slurk Belgian Blonde, Slurk Eng (Raspberry Wit), Slurk Hav (Seaweed Wit)
Aging: Slurk Whirled White Wheat (Wit)
Fermenting:
Next brew: Slurk Hav

Offline tom_hampton

  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 929
  • BeerSmith 2 Rocks!
    • Tom's Miata Racing Blog
Re: BS2: evaporation rate, could I adjust it?
« Reply #4 on: October 01, 2012, 11:33:35 AM »
NOTE:  Ideally, you WANT a boiloff between 12 and 15% per hour.  If you are not exceeding 12% per hour, then you are likely not evolving all of the DMS that is produced during the boil. 

This is a risk anytime you are using 2-row, 6-row, or pilsener Malts.  The heat from roasting Pale malts and darker destroys the SMM in the grain, so they do not have this risk. Thus, you can boil those as slowly as you wish.  Slower boiling will have a minor effect on hops utilization due to decreased wort circulation. 

So, if you are making a german pilsener, light lager, Saison or anything using one of the palest base malts...turn your flame UP and boil-off more. 
R.I.P.:Belgian Blonde
On Tap: Apfelwein, Kolsch(v2), Pumpkin Ale, Belgian Specialty 
Aging/Storing: Coffee Porter, Chocolate Porter, Flanders Red, English Barlywine
Fermenting: Maggie's Altbier
Next Up: PtE(1.1), Belgian Dubbel?

Working thru all BCS recipes

Offline Slurk

  • Slurk
  • BeerSmith Grandmaster Brewer
  • *****
  • Posts: 370
  • Life is too short!
    • SLURK BEER  By Foeyn Minibryggeri
Re: BS2: evaporation rate, could I adjust it?
« Reply #5 on: October 01, 2012, 03:18:41 PM »
Thanks Tom!
Yes, I agree DMS could be a nasty one when brewing German pilsener and lagers. And you know I am brewing those and want vigarous boils.
My set up is a 30L boiling kettle that I heat on the electrical kitchen stove, so far so good. The electrical kitchen stove is this "self thinking" system that regulates output/heat. However, sometimes she (it is a she) "thinks" different from what I would like to see from her (I can't change her personality and I can't change her mood:)). This is from time to time frustrating especially since I am a real fan of Asian wok food (needs high temperatures) and the other hobby..... brewing beer. Murphey's law is also involved here (she is more moody when having guests over for dinner etc.)
Last saturday, after a long period of being nice and dedicated, she was moody again. I got the wort to a boil, but not a real vigarous boil as I would like. She might have thought that this was more than good enough for me. I decided to split up the wort in a 10L and a 18L parallel boil. I lost some time on this in the beginning, but it worked fine after all.
Regards,
Slurk
Ad Fundum!

Ready to drink: Slurk Fjellbrygg, Slurk Foeyn Ale, Slurk Agurk (Cucumber Wit), Slurk Belgian Blonde, Slurk Eng (Raspberry Wit), Slurk Hav (Seaweed Wit)
Aging: Slurk Whirled White Wheat (Wit)
Fermenting:
Next brew: Slurk Hav

 

modification